PE Series Jaw Crusher

PE Series Jaw Crusher

One of the most popular gravel equipment in the world of gravel, PE Series Jaw Crusher is most suitable for primary and secondary crushing.The highest anti - pressure crushed material strength 320 mpa.Based on years of experience and technology development, the zenith PE jaw crusher series of 6 different models, can meet the requirements of most in primary and secondary crushing and broken.Flexible discharge outlet set up relative equipment jaw crusher to allow a perfect match.Zenith jaw crusher is easy to install, operate and maintain.

Detailed Introduction

Technical Features And Advantages

  • 1. The application of world-class manufacturing processes and high-tech materials;
  • 2. Integrated steel structures are used for the base of bearing;
  • 3. The crushing chamber uses "V"-shaped structure, so that the feeding size equal to the nominal one;
  • 4. The crushing chamber is deep and without dead zone, increases the capacity and the output;
  • 5. Lubrication system is safe and reliable, convenient to replace parts, easy to maintain;
  • 6. The outlet employs shim adjustment system, convenient and reliable, and increase the flexibility of the equipment;
  • 7. Low noise, less dust.

Jaw Crusher Operation Method

  • 1. Jaw Crusher No-load test
  • (1) jaw crusher continuous operation for 2 hours, the bearing temperature rise shall not exceed 30℃.

    (2) all fasteners should be solid, no loosening phenomenon.

    (3) flywheel, trough running smoothly.

    (4) all the friction parts without scratches, debris and grinding phenomenon, no normal sound.

    (5) the discharge port adjustment device should be able to ensure that the discharge port adjustment range.

  • 2. Jaw crusher with test load
  • (1) Jaw crusher shall not have a periodic or significant impact, impact sound.

    (2) the maximum feed size should meet the design requirements.

    (3) continuous operation 8h, bearing temperature rise shall not exceed 30℃.

  • 3. Preparation of jaw crusher before use
  • (1) carefully check the bearing lubrication is good, thrust plate connection is sufficient grease.

    (2) carefully check all fasteners are fastened.

    (3) carefully check the belt is good. If you find a broken phenomenon, it should be replaced, when the belt or pulley on the oil, the application of wiping the oil wipe.

    (4) check the protective device is good, found that there is an unsafe phenomenon, it should be promptly excluded.

    (5) check the crushing chamber with or without ore or debris, if the ore or debris, you must clean up to ensure that the jaw crusher cavity start.

    (6) Check whether the top bolts are returned, whether the gasket is tightened, T-bolts are tightened. Jaw crusher driver must be trained to achieve the "three understand" (understand the structure, understand the performance, understand the principle), "four will" (will use, will be maintained, will be maintained, will deal with failure), the training test pass, After the certificate, the standard quasi-operation.

Jaw Crusher Operation Tips

  • 1, according to the use of gravel rolling trough should be set on top of the protective cover, to prevent the gravel from the rolling groove within the collapse of injury.
  • 2, before starting, to clear the jaw crusher and the surrounding debris, must check the lubrication parts, and hand to move a few laps, the flexibility of the agencies to allow the boot.
  • 3, jaw crusher work, it is strictly prohibited to remove the stone from the palmar palette, if the application of crowded sticks, hooks and other tools to deal with.
  • 4, if the material broken due to broken cavity caused by parking, should immediately turn off the motor, until the material removed clean, and then start.
  • 5, adjust the discharge port, you should first release the tightening spring, to be adjusted, and then adjust the spring tension and tighten the bolt to prevent the liner off at work.
  • 6, jaw crusher work, to prevent the stone embedded in the tension spring, and affect the spring strength.

Technical Data

Model Feed Opening (mm) Max Feeding (mm) Discharge Opening (mm) Capacity (t/h) REV (r/min) Power (kw) Motor Model Machine Size (mm)
PE200×350 200×350 170 20-50 2-6 220 6-7.5 Y160M-6/7.5
PE250×400 250×400 210 20-60 5-20 310 6-15 Y180L-6/15 1450×1315 ×1296
PE250×750 250×750 210 20-60 8-22 320 6-30 Y225M-6/30
PE500×750 500×750 425 50-100 45-100 275 6-55 Y280M-6/55 1890×1916 ×1870
PE600×900 600×900 500 65-160 70-120 250 6-75 Y315S-6/75 2520×1840 ×2303
PE750×1060 750×1060 630 80-140 130-260 250 8-90 Y315L1-8/90 2620×2302 ×3110
PE900×1200 900×1200 750 95-165 220-380 200 8-130 JR127-8/130 3789×2826 ×3025
PE1000×1200 1000×1200 850 195-265 230-380 200 8-130 JR127-8/130 3889×2826 ×3025
PE1200×1500 1200×1500 1020 150-300 400-800 220 8-200 YR355M4-8/200 4930×3150 ×3700

Inquiry

Simply complete the form below, click submit, you will get the price list and a Zenith representative will contact you within one business day. Please also feel free to contact us by email or phone. ( * Denotes a required field).